When a property in Andrews changes hands, gets a new tenant, or simply reaches the point where someone needs to know what the wiring actually looks like, an electrical safety inspection is where that conversation starts. We go through the panel, the branch circuits, the grounding and bonding, the protection devices, and any visible wiring condition that needs to be documented. What we find gets explained plainly, not handed over as a report full of jargon. You know what is there, what it means, and what the options are before any decision has to be made.
We handle that work for Andrews and the surrounding area, for homes that have been standing a while and for commercial spaces that need a clear picture before a build-out or a lease. We cover the full range of residential and commercial electrical work here, and the process is the same regardless of the job size: scope it on the call, confirm the price before anything is scheduled, and show up ready to handle what was discussed.
Some electrical problems announce themselves. A breaker trips and stays tripped. An outlet goes dead. A fixture stops working. Those are straightforward to locate and fix.
Others take more finding. A circuit that trips only when a particular combination of things is running. A fault that only shows up after rain gets into a conduit or a junction box. An intermittent problem that was fine all morning and failed again by afternoon. These take diagnostic work that goes beyond swapping a device and calling it done. We trace the circuit, check the connections, test under load, and find where the fault actually lives rather than where it first shows up.
GFCI and AFCI protection can complicate the picture too. An arc-fault breaker that trips without an obvious cause is often picking up something real in the wiring, and resetting it repeatedly without finding the source is not a fix. We work through what the protection device is responding to, not just whether it will hold after a reset.
Electrical pricing depends on what the job actually involves, and that is not evasion. It is how the work is structured.
What moves a quote is the fault itself, what has to be opened up to reach it, and whether the existing circuit or panel can carry what is being added. A dedicated circuit for a new appliance is a different scope than running the same circuit when the panel is already at capacity and needs to be upgraded first. A single outlet replacement is a different conversation than finding out why three outlets on the same circuit stopped working.
We go through all of that on the call. You describe what is happening or what you want done, we ask the questions that help us scope it, and you get a price before anything is scheduled. That price covers what was discussed. If we get there and the situation is different from what the call indicated, we tell you before doing anything additional. No-pressure estimates, priced up front, is how we work.
Some faults can wait a few days. A dead outlet in a spare room, a dimmer that stopped responding, a fixture that needs replacing. We schedule those the normal way, confirm the time, and come out when it suits you.
Others cannot wait. A panel that will not hold, a burning smell near a breaker, a circuit that has gone out in a space a business is trading from. We take short-notice work where the schedule allows, and when you call and describe what is happening, we are honest about what is available rather than making a promise we cannot keep.
A property that has to stay occupied or a business that cannot close for a day is a scheduling problem as much as an electrical one. We plan around it. Some jobs only need one circuit isolated, not a full shutdown. Where a shutdown is unavoidable, we talk through the scope and the timing before the visit so you can plan around it. A home office, a retail space, a workshop that has to keep running, these are conversations we have on the call rather than problems we figure out when we arrive.
Not all electrical work is done the same way, and a property that has had additions, renovations, or repairs over the years sometimes carries forward wiring that was done without permits, with the wrong materials, or in a way that made sense at the time but does not hold up now.
When we find that kind of work, we assess what can be corrected in place and what has to come out. A junction box that was buried in a wall without access can sometimes be relocated. Wiring that was connected with the wrong connectors for its conductor type, aluminum branch circuits joined to devices not rated for them, undersized wire on a circuit that was later loaded up, these are conditions that need to be addressed rather than worked around.
We explain what we find without making a production of it. You hear what the condition is, what the practical options are, and what each one involves. Grounding and bonding issues that turn up during a panel inspection get the same treatment: a clear explanation of what is present and what it takes to bring it to current standards.
A full-panel shutdown is not always what a job requires. Replacing an outlet, adding a circuit, swapping a breaker, these can often be done with only the affected circuit isolated. A panel replacement, a service-entrance upgrade, or a rewire of multiple circuits is a different matter. We tell you on the call which category the job falls into.
When a full shutdown is unavoidable, the timing matters. A home where someone is working remotely needs a different plan than a vacant property. A business that opens at a set hour needs the work completed before that. We confirm the scope and the expected duration before scheduling so you can plan accordingly. We do not promise a specific finish time, but we do not leave you guessing about what the day involves.
A dedicated circuit means the appliance or equipment has a breaker and a run of wire sized specifically for its load, without sharing capacity with anything else on the panel. Dryers, ranges, chest freezers, and workshop equipment all draw enough current that a shared circuit is a recipe for repeated trips. Hot tub wiring adds GFCI protection requirements and a disconnect at the equipment. We handle the circuit from the panel to the point of connection.
A Level 2 home EV charger runs on a dedicated 240-volt circuit, and the first question is always whether the panel can carry the added load. We run a load calculation, confirm what the panel supports, and run the circuit to where the charger will be mounted. If the panel needs to be upgraded before the circuit can be added, we scope that as part of the same call.
Homes in this part of West Texas that are running continuous air conditioning loads alongside modern appliances and charging equipment can push an older panel close to its limit. A service upgrade to a higher amperage involves a load calculation, a new main panel, and in many cases a service-entrance upgrade at the meter. We handle the utility coordination where it is required.
Outdoor wiring in this region takes sustained heat and sun exposure. We install exterior fixtures, security lighting, motion-activated lights, and landscape lighting circuits, and we make sure the runs are protected against the conditions. Exterior outlets for patios, RV hookups, and misting-system circuits are part of the same category of work.
We serve Andrews and McKinney Acres, and we take calls from across Andrews County. You're talking to someone who knows the area and the homes in it. Coverage is not conditional on the job size or the property type. Residential, commercial, and everything in between is on the table.
If you are not sure whether you fall inside the area we cover, call and ask. We will tell you straight. The specifics for a job like this are on our full list of electrical services.
When electrical rough-in happens after framing is closed or after other trades have finished their work, the cost and complexity of running wiring increases significantly. Walls that are already finished may need to be opened, and some routing options that were available during framing are no longer accessible. Getting us on site during the framing stage avoids that situation.
Yes. Circuits are tested before we leave to confirm they are wired correctly, protected properly, and functioning as expected. We do not consider a job finished until the work has been verified.
Yes. Landlords and property managers with multiple properties can call and discuss what needs to be done across locations. We scope each property individually and schedule the work in a way that fits the portfolio, whether that means back-to-back visits or separate scheduling as needs come up.
An electric range needs a dedicated 240-volt circuit sized for the load the range draws, which is typically a 50-amp circuit with the appropriate outlet or hardwired connection. We confirm the panel has capacity for the circuit, run the wiring, and install the outlet or make the connection at the appliance location.
The wiring side is electrical work. Sauna heaters and steam generators typically require a dedicated 240-volt circuit sized for the unit's draw, and we handle that circuit, the appropriate outlet or connection, and any panel work the load requires. The unit itself and any plumbing or enclosure work are separate trades.
You do not need to know what is causing it before you call. Describing what you are seeing is enough. We ask the questions that help us figure out the rest, scope the job on the call, and give you a price before anything is scheduled.
Call (432) 326-6289. We are available every day from 8:00 AM to 8:00 PM.
Close by, we also take electrical work in: Midland, West Odessa, Kermit, Stanton.
See our service area list.
We handle the full range of electrical work for homes and businesses across Andrews and Andrews County, from a single tripped breaker to a complete service upgrade. The table below covers what each service involves, who it fits, and what is worth knowing before you call. Scope is confirmed on the phone, and the price is settled before anything is scheduled.
Call (432) 326-6289 and tell us what you are dealing with.
| Electrical Service | What the Job Involves | Best For | Worth Knowing |
|---|---|---|---|
| Outlet & Switch Installation |
| Homeowners adding convenience or updating older outlets | GFCI outlets can be installed in ungrounded locations as a code-recognized method of providing shock protection, labeled correctly. |
| Solar & Battery Installation |
| Homeowners adding solar or battery storage systems in West Texas | We handle the electrical infrastructure side. The solar equipment itself is a separate trade. Our piece is the wiring, circuits, and panel work that makes the system run safely. |
| Electrical Panel & Service Upgrades |
| Homes adding EV chargers, solar systems, or high-draw equipment, and older homes with undersized panels | Andrews summers put continuous heavy load on panels. We run a load calculation to find out exactly what your service can carry before recommending any upgrade. |
Call (432) 326-6289 to talk through what you are dealing with and get a straight answer on what it will take to fix it.
(432) 326-6289